Marlin Firearms Forum banner

1 - 5 of 5 Posts

·
Registered
Joined
·
181 Posts
Discussion Starter #1
Hi all anyone have any data on this setup or something close.

I have loaded using H322 data which I believe is one of the equilants.

Loaded 20 at 29grs and 10 at the full Lee scope 2.2CC I believe.

Any advice will be good, still waiting for the PTA's to clear and get gun before testing rounds.

Thanks in advance.

Sorry rifle will be marlin 336BL (new - so I suppose 2012 or 2013)
 

·
Registered
Joined
·
1,167 Posts
Go to the ADI website. Very good data. They had no load data for the FTX and monoflex in 30-03 or 308ME, so I asked and they sent it back. Be wary about equivalents as they may be similar but not exact matches.
Happy reloading and stay on the safe side.
 

·
Registered
Joined
·
181 Posts
Discussion Starter #3
From Quickload,

Cartridge : .30-30 Win. (SAAMI)
Bullet : .308, 150, Sierra SPFN 30-30 2000
Useable Case Capaci: 36.983 grain H2O = 2.401 cm³
Cartridge O.A.L. L6: 2.550 inch = 64.77 mm
Barrel Length : 18.5 inch = 469.9 mm
Powder : ADI AR 2219

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 70 24.80 1829 1114 23351 5368 86.6 1.407
-18.0 72 25.42 1872 1167 24747 5549 87.9 1.374
-16.0 74 26.04 1915 1222 26227 5726 89.1 1.341
-14.0 76 26.66 1959 1278 27794 5899 90.2 1.310
-12.0 77 27.28 2002 1335 29456 6068 91.3 1.279
-10.0 79 27.90 2045 1393 31216 6232 92.4 1.249
-08.0 81 28.52 2089 1453 33083 6391 93.4 1.220
-06.0 83 29.14 2132 1514 35064 6544 94.3 1.190
-04.0 85 29.76 2175 1576 37166 6691 95.1 1.163 ! Near Maximum !
-02.0 86 30.38 2218 1639 39398 6831 95.9 1.132 ! Near Maximum !
+00.0 88 31.00 2262 1704 41770 6964 96.6 1.103 !DANGEROUS LOAD-DO NOT USE!
+02.0 90 31.62 2305 1769 44291 7089 97.3 1.074 !DANGEROUS LOAD-DO NOT USE!
+04.0 92 32.24 2347 1835 46972 7205 97.9 1.047 !DANGEROUS LOAD-DO NOT USE!
+06.0 93 32.86 2390 1903 49828 7313 98.4 1.020 !DANGEROUS LOAD-DO NOT USE!
+08.0 95 33.48 2433 1971 52869 7412 98.8 0.994 !DANGEROUS LOAD-DO NOT USE!
+10.0 97 34.10 2475 2040 56111 7501 99.2 0.970 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 15% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 15% relative to nominal value:
+Ba 88 31.00 2419 1948 54308 6810 100.0 0.991 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 15% relative to nominal value:
-Ba 88 31.00 2029 1372 31053 6342 84.5 1.249

Seems ok to me.
 

·
Registered
Joined
·
150 Posts
There is usually more detail available on Hodgdon's site (pressure data).

If you are looking for a bit more velocity, then something like ADI 2206H (=H4895) should give you around 200 fps more velocity in top loads.

FWIW ADI 2219 will work well in your 45/70 if you are looking for high velocity loads.
 
1 - 5 of 5 Posts
Top